Netcat is a featured networking utility which reads and writes data across network connections, using the TCP/IP protocol.
It provides access to the following main features:
- Outbound and inbound connections, TCP or UDP, to or from any ports.
- Featured tunneling mode which allows also special tunneling such as UDP to TCP, with the possibility of specifying all network parameters (source port/interface, listening port/interface, and the remote host allowed to connect to the tunnel.
- Built-in port-scanning capabilities, with randomizer.
- Advanced usage options, such as buffered send-mode (one line every N seconds), and hexdump (to stderr or to a specified file) of trasmitted and received data.
- Optional RFC854 telnet codes parser and responder.
nc [-46bCDdhklnrStUuvZz] [-I length] [-i interval] [-O length]
[-P proxy_username] [-p source_port] [-q seconds] [-s source]
[-T toskeyword] [-V rtable] [-w timeout] [-X proxy_protocol]
[-x proxy_address[:port]] [destination] [port]
-4 Forces nc to use IPv4 addresses only.
-6 Forces nc to use IPv6 addresses only.
-b Allow broadcast.
-C Send CRLF as line-ending.
-D Enable debugging on the socket.
-d Do not attempt to read from stdin.
-h Prints out nc help.
-I length Specifies the size of the TCP receive buffer.
-i interval Specifies a delay time interval between lines of text sent and received. Also causes a delay time between connections to multiple ports.
-k Forces nc to stay listening for another connection after its current connection is completed. It is an error to use this option without the -l option.
-l Used to specify that nc should listen for an incoming connection rather than initiate a connection to a remote host. It is an error to use this option in conjunction with the -p, -s, or -z options. Additionally, any timeouts specified with the -w option are ignored.
-n Do not do any DNS or service lookups on any specified addresses, hostnames or ports.
-O length Specifies the size of the TCP send buffer.
-P proxy_username Specifies a username to present to a proxy server that requires authentication. If no username is specified then authentication will not be attempted. Proxy authentication is only supported for HTTP CONNECT proxies at present.
-p source_port Specifies the source port nc should use, subject to privilege restrictions and availability.
-q seconds after EOF on stdin, wait the specified number of seconds and then quit. If seconds is negative, wait forever.
-r Specifies that source and/or destination ports should be chosen randomly instead of sequentially within a range or in the order that the system assigns them.
-S Enables the RFC 2385 TCP MD5 signature option.
-s source Specifies the IP of the interface which is used to send the packets. For UNIX-domain datagram sockets, specifies the local temporary socket file to create and use so that datagrams can be received. It is an error to use this option in conjunction with the -l option.
-T toskeyword Change IPv4 TOS value. toskeyword may be one of critical, inetcontrol, lowcost, lowdelay, netcontrol, throughput, reliability, or one of the DiffServ Code Points: ef, af11 ... af43, cs0 ... cs7; or a number in either hex or decimal.
-t Causes nc to send RFC 854 DON'T and WON'T responses to RFC 854 DO and WILL requests. This makes it possible to use nc to script telnet sessions.
-U Specifies to use UNIX-domain sockets.
-u Use UDP instead of the default option of TCP. For UNIX-domain sockets, use a datagram socket instead of a stream socket. If a UNIX-domain socket is used, a temporary receiving socket is created in /tmp unless the -s flag is given.
-V rtable Set the routing table to be used. The default is 0.
-v Have nc give more verbose output.
-w timeout Connections which cannot be established or are idle timeout after timeout seconds. The -w flag has no effect on the -l option, i.e. nc will listen forever for a connection, with or without the -w flag. The default is no timeout.
-X proxy_protocol Requests that nc should use the specified protocol when talking to the proxy server. Supported protocols are "4" (SOCKS v.4), "5" (SOCKS v.5) and "connect" (HTTPS proxy). If the protocol is not specified, SOCKS version 5 is used.
-x proxy_address[:port] Requests that nc should connect to destination using a proxy at proxy_address and port. If port is not specified, the well-known port for the proxy protocol is used (1080 for SOCKS, 3128 for HTTPS).
-Z DCCP mode.
-z Specifies that nc should just scan for listening daemons, without sending any data to them. It is an error to use this option in conjunction with the -l option.
For further reference,